CADE: lecturer at Seminar of Energy – CIEMAT

CADE will be present as a lecturer on the 2nd Edition of the Energy Seminar that will be held next February 23rd 2016 at CIEMAT headquarters.

The event, hosts by ANSYS and CIEMAT, seeks the goal of being a meeting place for the energy sector with testimonies of clients, and focused on ANSYS Version 17.0 latest innovations.
Event Agenda

08:30 Inscription and Welcome coffee
09:00 Introduction to CIEMAT activities. Energy, environment and associated technologies – José Manuel Pérez, CIEMAT
09:20 ANSYS in the energy sector. Trends and Vision – Gilles Lebiez and Mariano Morales, ANSYS
09:45 ANSYS Mechanical 17.0 latest innovations – Mariano Morales, ANSYS
10:10 ANSYS CFD 17.0 innovations – Pedro Afonso, ANSYS
10:40 CIEMAT Technical presentation
11:30 Coffee Break
12:00 ITMA/Duro Felguera Lecture
12:20 Engineering and advance simulation: High value solutions in Power Genereration – Javier Martinez Carrillo, CADE Soluciones de Ingeniería
12:40 Scaling fluidized beds for hydrogen production by improved methane reformer – Carlos Herce Fuente, CIRCE
13:00 ANSYS models for ABENGOA technical development – José María Mendez Marcos, Abengoa Research
13:20 Advantages (and limitations) of ANSYS Workbench and SpaceClaim from the perspective of systems spectral analysis on ITER – S. Ochandiano y A. Cañete, Empresarios Agrupados
13:40 Seminar Closing speech – Enrique González, ANSYS + Reception
Study of deformations and the prestressing process in pressure equipment flanges

Study of deformations and the prestressing process in pressure equipment flanges

The flanged joints of pressure equipment can show deformations due to the bolt tightening process, or being generated later during service. The appearance of this type of problem may mean that the equipment is not suitable to continue with the operation, with the consequent economic impact that would entail a stop, repair or replacement of the affected components. Through FEA simulation […]

Design and FEM analysis of equipment and conductors made of fiber reinforced plastic (FRP)

Design and FEM analysis of equipment and conductors made of fiber reinforced plastic (FRP)

There are many sectors (chemical and process industry, naval, aeronautical or food sector) and industrial applications in which it is necessary to design and validate equipment made with special materials (FRP- Fiberglass Reinforced Plastic), due to to the special corrosion resistance requirements for which they have to provide service. This is the case of pressure […]

Fitness for service procedures for cracks like flaws

Fitness for service procedures for cracks like flaws

During the life cycle of many pressure vessels arise the necessity to maintain them in service after detecting crack-like flaws or delamination. For that, there are some methodologies that allow establishing a quantitative judgment about if it is possible to safely operate this equipment and also determine its remaining life until it must be repaired […]

STRESS ANALYSIS OF PIPES WITH RATIO D / t> 100

STRESS ANALYSIS OF PIPES WITH RATIO D / t> 100

On certain occasions, during the development of projects where large diameter pipes are involved, scenarios arise in which the diameter (D) / thickness (t) ratio is higher than 100. It is common to find this situation in systems with large diameter pipes that work at low pressure, in which the calculated thickness due to the […]

CFD analysis of heat recovery boilers– HRSG

CFD analysis of heat recovery boilers– HRSG

Computational Fluid Dynamics (CFD analysis) simulation of HRSG Boilers turns out to be a powerful engineering methodology in order to determine an optimal design to achieve maximum efficiency and avoid future operation issues, (such as incorrect mixing ratio, asymmetric burner performance, among others.). This type of simulations allows to analyze the behaviour of the chemical […]

Fitness for Service – Alternatives for equipment validation

Fitness for Service – Alternatives for equipment validation

Boiler and pressure equipment manufacturers face everyday strict design and manufacturing requirements to supply heat exchangers, pressure vessels or process equipment. The recognized international design and manufacturing codes that are prescribed for this type of equipment (ASME VIII Div. 1 & 2, EN13445, AD2000, etc.) specify those tests, trials, inspections and quality controls to be […]

1 2 3 4